Category: 288-36-8

Electric Literature of 288-36-8, New discoveries in chemical research and development in 2021. We’ll be discussing some of the latest developments in chemical about CAS: 288-36-8, name is 1H-1,2,3-Triazole, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc, below Introduce a new synthetic route.

Intermediate 46: 6-Methyl-2-[1 ,2,3]triazol-2-yl-nicotinic acid.To a 100 ml round bottom flask containing 2-chloro-6-methylnicotinic acid (3 g, 17.4 mmol), copper iodide (0.16 g, 0.5 mol%), and cesium carbonate (1 1 .4 g, 35 mmol) was added a mixture of dioxane (20 ml_) and H2O (0.1 ml, 5.25 mmol). Next triazole (2.03 ml_, 35 mmol) and finally (R,R)-(-)-N,N’-dimethyl-1 ,2- cyclohexanediamine ligand (0.56 ml_, 3.5 mmol) were added. The resulting clumpy yellow slurry was stirred until evenly dispersed. Upon heating to 100 C the reaction mixture changed from a yellow slurry to pale green. As heating progressed the slurry became less thick and was stirred more easily. The light green slurry was stirred for 4 hr at 100 C and left to stir at room temp overnight. At this point the reaction mixture appeared as a cobalt blue slurry which was then diluted with 20 ml_ ether and 20 ml_ H2O. The resulting solution was thoroughly stirred and transferred to a seperatory funnel then the RBF was subsequently rinsed with 20 ml_ ether and H2O each. The aqueous layer was separated from the organic layer and acidified to pH 1 with 6 ml_ cone. HCI.The now brown/ lime green aqueous layer was extracted twice with EtOAc. The bright yellow organic layers were combined and dried with Na2SO4 and then cone, into a yellow powder under reduced pressure. To the yellow powder was added EtOAc to form a yellow slurry. The solids were filtered off and washed with EtOAc to give a very pale yellow powder, which was found by 1H NMR to be Intermediate 53 (25% yield). The filtrate was cone, into a yellow solid and purified by FCC using 0-5% MeOH in DCM w/ 0.5% AcOH to give the title compound in a 20% yield. MS (ESI): mass calculated for C9H8N4O2, 204.18; m/z found 205.3 [M+H]+. 1 H NMR (400 MHz, CD3OD): 8.21 – 8.18 (m, 1 H), 7.98 (s, 2H), 7.51 (d, J = 7.9 Hz, 1 H), 2.64 (s, 3H).Intermediate 49: 6-Methyl-2-[1 ,2,3]triazol-1 -yl-nicotinic acid.The title compound was isolated from the procedure used to prepareIntermediate 46 with a 25% yield. MS (ESI): mass calculated for ?9?8?4?2, 204.18; m/z found 205.3 [M+H]+. 1H NMR (400 MHz, CD3OD): 8.48 (d, J = 1 Hz, 1 H), 8.25 (dd, J = 7.9, 3.8 Hz, 1 H), 7.88 (d, J = 1 .1 Hz, 1 H), 7.54 (d, J = Hz, 1 H), 2.64 (s, 3H).

I am very proud of our efforts over the past few months and hope to 1H-1,2,3-Triazole help many people in the next few years.

Reference:
Patent; JANSSEN PHARMACEUTICA NV; BRANSTETTER, Bryan, James; LETAVIC, Michael, A.; LY, Kiev, S.; RUDOLPH, Dale, A.; SAVALL, Brad, M.; SHAH, Chandravadan, R.; SHIREMAN, Brock, T.; WO2011/50202; (2011); A1;,
1,2,3-Triazole – Wikipedia,
Triazoles – an overview | ScienceDirect Topics

Related Products of 288-36-8, New Advances in Chemical Research in 2021. Chemo-enzymatic cascade processes are invaluable due to their ability to rapidly construct high-value products from available feedstock chemicals in a one-pot relay manner. 288-36-8, name is 1H-1,2,3-Triazole, molecular formula is C2H3N3, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, below Introduce a new synthetic route.

Example 14: 5-[l-tert-Butyl-2-(2-l,2,3-triazol-2-yl-phenyl)-lH-benzimidazol-5-yl]- pyrimidin-2-ylamine and Example 15: 5-[l-tert-Butyl-2-(2-l,2,3-triazol-l-yl-phenyl)-lH-benzimidazol-5-yl]- pyrimidin-2-ylamine29% 13%To a solution of 5-[2-(2-bromo-phenyl)- l-ieri-butyl- lH-benzimidazol-5-yl]-pyrimidin-2- ylamine (refer to example 8, step 1) (57 mg, 0.14 mmol) in DMF (5 mL) are added 1Eta- 1,2,3-triazole (0.012 mL, 0.2 mmol), CuO (1 mg, 0.013 mmol), Fe(acac)3 (14 mg, 0.04 mmol) and Cs2C03 (88 mg, 0.27 mmol) at room temperature. The mixture is heated at 120 C for 96 hours and then cooled down and filtered. The filtrate is extracted with H20 (10 mL) and EtOAc (3 x 10 mL). The combined organic layer is dried with MgS04 and is filtered. The filtrate is concentrated and the residue is purified by silica gel chromatography eluting with 5% MeOH in CH2C12 to afford a less polar product 5-[l- ieri-butyl-2-(2- l,2,3-triazol-2-yl-phenyl)-lH-benzimidazol-5-yl]-pyrimidin-2-ylamine (Example 14) (16 mg, 29%) LCMS (ESMS): m/z 411.68 (M++l) as the major product and a more polar product 5-[l-ieri-butyl-2-(2-l,2,3-triazol-l-yl-phenyl)- lH- benzimidazol-5-yl]-pyrimidin-2-ylamine (Example 15) (7 mg, 13%) LCMS (ESMS): m/z 411.68 (M++l) as the minor product.

We very much hope you enjoy reading the articles and that you will join us to present your own research about 288-36-8, Happy reading!

Reference:
Patent; BOEHRINGER INGELHEIM INTERNATIONAL GMBH; CHEN, Zhidong; HAO, Ming-Hong; LIU, Weimin; LO, Ho-Yin; LOKE, Pui Leng; MAN, Chuk, Chui; MORWICK, Tina, Marie; NEMOTO, Peter, Allen; TAKAHASHI, Hidenori; TYE, Heather; WU, Lifen; WO2011/68821; (2011); A1;,
1,2,3-Triazole – Wikipedia,
Triazoles – an overview | ScienceDirect Topics

Research speed reading in 2021. In classical electrochemical theory, both the electron transfer rate and the adsorption of reactants at the electrode control the electrochemical reaction. 288-36-8, name is 1H-1,2,3-Triazole belongs to triazoles compound, it is a common compound, a new synthetic route is introduced below. HPLC of Formula: C2H3N3

Examples 61 and 62; The product of preparation 53 (500mg, 1. 98mmol), 1H-1, 2, 3-triazole (204mg, 2. 96mmol) and potassium carbonate (546mg, 3. 96mmol) were stirred for 18 hours in a mixture of acetonitrile (5mL) and N, N-dimethylformamide (2mL). The solvent was then evaporated under reduced pressure and the residue was partitioned between ethyl acetate (20mL) and water (10mL). The organic phase was separated, washed with 1M hydrochloric acid (3x10mL), sodium hydrogen carbonate solution (10mL) and brine (10mL), dried over magnesium sulfate and concentrated in vacuo to provide an intermediate residue. The residue was then dissolved in xylene (7mL) and 2-methoxy-5-aminopyridine (491mg, 4mmol) and para-toluenesulfonic acid (cat) were added. The reaction mixture was heated at 140C for 6 hours then the solvent was evaporated under reduced pressure. The resulting black residue was partitioned between ethyl acetate (30mL) and water (10mL). The organic phase was separated, washed with citric acid (2x10mL), sodium hydrogen carbonate solution (10mL) and brine (10mL), dried over magnesium sulfate and concentrated in vacuo to provide a pale yellow oil. Purification by column chromatography on silica gel, eluting with pentane: ethyl acetate, 80: 20 to 20: 80, afforded the title compound of example 61 as a solid in quantitative yield, 230mg. Further elution with pentane: ethyl acetate, 10: 90 to 0: 100, afforded the product of example 62 in quantitative yield. Example 61 5-[3-(4-Ethoxy-3-methyl-phenyl)-5-[1,2,3]triazol-2-ylmethyl-[1,2,4]triazol-4-yl]-2- methoxy-pyridine ‘H NMR (CDCi3, 400MHz) a : 1.40 (t, 3H), 2.15 (s, 3H), 3.95-4. 05 (m, 5H), 5.70 (s, 2H) 6.65-6. 75 (m, 2H), 7.00-7. 05 (m, 1H), 7.18-7. 25 (m, 1H), 7.35 (m, 1H), 7.55 (s, 2H) 7.90 (s, 1 H). MS APCI+ m/z 392 [MH] + Microanalysis : found (%) C (61.06), H (5.40), N (24.80) ; C20H21N7O2 requires: (%) C (61.36), H (5.40), N (25.05) Example 62 5-[3-(4-Ethoxy-3-methyl-phenyl)-5-[1,2,3]triazol-1-ylmethyl-[1,2,4]triazol-4-yl]-2- methoxv-yridine ‘H NMR (CDCI3, 400MHz) d : 1.40 (t, 3H), 2.15 (s, 3H), 3.95-4. 05 (m, 5H), 5.65 (s, 2H) 6.65-6. 75 (d, 1H), 6.78-6. 82 (d, 1H), 7.00-7. 05 (brd, 1H), 7.15-7. 20 (d, 1H), 7.35 (s, 1 H), 7.70 (s, 1 H) 7.80 (s, 1 H), 7.90 (brs, 1 H). MS APCI+ m/z 392 [MH] + Microanalysis : found (%) C (61.20), H (5.36), N (24.86) ; C20H2’N702 requires: (%) C (61.36), H (5.40), N (25.05)

Sometimes chemists are able to propose two or more mechanisms that are consistent with the available data. If a proposed mechanism predicts the wrong experimental rate law, however, the mechanism must be incorrect.Welcome to check out more blogs about 1H-1,2,3-Triazole, in my other articles.

Reference:
Patent; PFIZER LIMITED; PFIZER INC.; WO2005/82866; (2005); A2;,
1,2,3-Triazole – Wikipedia,
Triazoles – an overview | ScienceDirect Topics

New discoveries in chemical research and development in 2021. The dynamic chemical diversity of the numerous elements, ions and molecules that constitute the basis of life provides wide challenges and opportunities for research. 288-36-8, name is 1H-1,2,3-Triazole belongs to triazoles compound, it is a common compound, a new synthetic route is introduced below. category: Triazoles

in a polar solvent,DMF, 9,10-dibromoanthracene, triazole, potassium carbonate and copper oxide inthe preparation of the organic compound under heating; 9,10-dibromoanthracenewherein: three azole: potassium carbonate: copper oxide molar ratio of 2: 10:30: 1; The reaction temperature is1500 C, the reaction time of 18 hours

If you are hungry for even more, make sure to check my other article about 288-36-8, the application of this compound in the production field has become more and more popular.

Reference:
Patent; Tianjin Normal University; WANG, YING; (12 pag.)CN104497023; (2016); B;,
1,2,3-Triazole – Wikipedia,
Triazoles – an overview | ScienceDirect Topics

Electric Literature of 288-36-8, New discoveries in chemical research and development in 2021. We’ll be discussing some of the latest developments in chemical about CAS: 288-36-8, name is 1H-1,2,3-Triazole, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc, below Introduce a new synthetic route.

The 2 H – 1, 2, 3 – triazole (3.45 g, 50 mmol), 2 – iodo -5 – methyl benzoic acid (5.24 g, 20 mmol), cesium carbonate (11.72 g, 36 mmol), trans – N, N’ – dimethyl – 1, 2 – diaminocyclohexane (0.51 g, 3.6 mmol), cuprous iodide (0.38 g, 2 mmol) and N, N – dimethyl formamide (30 ml) are added to the 100 ml round bottom flask in a single port, under the protection of nitrogen reaction solution gradually raising the temperature to 100 C reaction 4 hours. Stopping the reaction, cooling, liquid water (60 ml) diluted with water and ethyl acetate (200 ml × 2) extraction. The water layer is acidified to pH concentrated hydrochloric acid for 1 – 2, then adding ethyl acetate (200 ml × 2) extraction, the resulting organic layer dried with anhydrous sodium sulfate, filtered, filtrate turns on lathe does after separation and purification by column chromatography (dichloromethane/methanol (v/v)=50/1) to obtain the title compound (yellow solid, 2.76 g, 68%).

Therefore, this conceptually novel strategy might open impressive avenues to establish green and sustainable chemistry platforms.In my other articles, you can also check out more blogs about 1H-1,2,3-Triazole.

Reference:
Patent; Guangdong Dongyangguang Pharmaceutical Co., Ltd.; Jin Chuanfei; Zhang Yingjun; Xue Yaping; Lao Jinhua; Nie Biao; Xu Juan; (35 pag.)CN107759620; (2018); A;,
1,2,3-Triazole – Wikipedia,
Triazoles – an overview | ScienceDirect Topics

New discoveries in chemical research and development in 2021. The transformation of simple hydrocarbons into more complex and valuable products via catalytic C–H bond functionalisation has revolutionised modern synthetic chemistry. 288-36-8, name is 1H-1,2,3-Triazole belongs to triazoles compound, it is a common compound, a new synthetic route is introduced below. 288-36-8

To a round-bottomed flask equipped with an overhead magnetic stirrer, reflux condenser, and nitrogen inlet were added 2-Fluoro-6-iodobenzoic acid (2.5 g, 9.4 mmol), Cul (0.09 g, 0.47 mmol), and CS2CO3 (6.1 g, 18.8 mmol). To these solids were added dioxane (12.5 ml_), water (0.05 ml_), 1 H-1 ,2,3-triazole (1.09 ml_, 18.8 mmol), and finally (1 R,2R)-N1 ,N2-dimethylcyclohexane-1 ,2-diamine (0.3 ml_, 1.88 mmol). The mixture was then warmed to 100 C ON. The day after the mixture was cooled and MTBE and water were added. After vigorous mixing, the layers were separated and the bottom aqueous layer was acidified to pH 2 with 6N HCI. The aqueous phase was then extracted with DCM (3x). The combined organic layers were dried, and concentrated The residue was purified by FC on S1O2 column (eluent : from DCM to DCM:MeOH 90:10) to afford 2-fluoro-6-(2H-1 ,2,3-triazol-2-yl)benzoic acid (p186, 1.1 g, y= 56%). MS (m/z): 208.0 [M+H]+

I hope this article can help some friends in scientific research. I am very proud of our efforts over the past few months and hope to 1H-1,2,3-Triazole help many people in the next few years.

Reference:
Patent; CHRONOS THERAPEUTICS LIMITED; MICHELI, Fabrizio; BERTANI, Barbara; GIBSON, Karl Richard; DI FABIO, Romano; RAVEGLIA, Luca; ZANALETTI, Riccardo; CREMONESI, Susanna; POZZAN, Alfonso; SEMERARO, Teresa; TARSI, Luca; LUKER, Timothy Jon; (275 pag.)WO2019/43407; (2019); A1;,
1,2,3-Triazole – Wikipedia,
Triazoles – an overview | ScienceDirect Topics

Synthetic Route of 288-36-8, New Advances in Chemical Research in 2021. As an important bridge between the micro and macro material world, chemistry is one of the main methods and means for humans to understand and transform the material world. 288-36-8, name is 1H-1,2,3-Triazole, molecular formula is C2H3N3, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, below Introduce a new synthetic route.

Intermediate 52: 3-Fluoro-2-(2H-1 ,2,3-triazol-2-yl)benzoic acid.Step A: 3-Fluoro-2-(2H-1 ,2,3-triazol-2-yl)benzonitrile and 3-fluoro-2-(1 H- 1 ,2,3-triazol-1 -yl)benzonitrile. A mixture of 2,3-difluorobenzonitrile (4.0 g, 28.8 mmol), 2H-1 ,2,3-triazole (1 .9 g, 28.8 mmol) in DMF (85.0 mL) and K2C03 (7.9 g, 57.5 mmol) were heated to 125 C for 1 .5 h. After cooling to rt, water was added and the mixture extracted with EtOAc (2 X). The combined organics were washed with brine and dried (Na2S04). Purification via FCC (10-100% EtOAc in hexanes) gave two products. 3-Fluoro-2-(2H-1 ,2,3-triazol-2- yl)benzonitrile (1 .6 g, 29%), 1H NMR (CDCI3): 7.99 (s, J = 6.6 Hz, 2H), 7.67 – 7.63 (m, 1 H), 7.61 – 7.53 (m, 2H), 7.26 (s, 6 H) and 3-fluoro-2-(1 H-1 ,2,3-triazol- 1 -yl)benzonitrile (2.0 g, 38%) 1H NMR (CDCI3): 7.97 (dd, J = 4.4, 2.8 Hz, 1 H), 7.95 (d, J = 1 .2 Hz, 1 H), 7.70 (tt, J = 5.7, 2.8 Hz, 1 H), 7.65 (td, J = 8.1 , 4.9 Hz, 1 H), 7.62 – 7.57 (m, 1 H).

Future efforts will undeniably focus on the diversification of the new catalytic transformations. These may comprise an expansion of the substrate scope from aromatic and heteroaromatic compounds to other hydrocarbons. Keep reading other articles of 288-36-8.

Reference:
Patent; JANSSEN PHARMACEUTICA NV; LETAVIC, Michael; RUDOLPH, Dale, A.; SAVALL, Brad, M.; SHIREMAN, Brock, T.; SWANSON, Devin; WO2012/145581; (2012); A1;,
1,2,3-Triazole – Wikipedia,
Triazoles – an overview | ScienceDirect Topics

New discoveries in chemical research and development in 2021. Chemo-enzymatic cascade processes are invaluable due to their ability to rapidly construct high-value products from available feedstock chemicals in a one-pot relay manner. 288-36-8, name is 1H-1,2,3-Triazole belongs to triazoles compound, it is a common compound, a new synthetic route is introduced below. 288-36-8

To a solution of 2-iodobenzoic acid (3.0 g, 12.1 mmol) in DMF was added 1,2,3- triazole (1.5 g, 21.7 mmol), Cs2CO3 (7.1 g, 21.7 mmol), Cul (114 mg, 0.6 mmol), and trans-N,N?dimethylcyclohexane- 1 ,2-diamine (310 mg, 2.2 mmol). After heating at 120 C for 10 mm in amicrowave reactor, the mixture was cooled to room temperature, diluted with EtOAc, and filtered through Celite. The filtrate was concentrated in vacuo and the crude residue was purified by silica gel chromatography (MeOH in DCM with 0.1% AcOH) to give Intermediate N as the faster eluting isomer. ?H NMR (DMSO-d6, 500MHz) oe 13.05 (brs, 1 H), 8.12 (s, 2H), 7.8 1-7.52 (m, 4H).

If you are hungry for even more, make sure to check my other article about 288-36-8, the application of this compound in the production field has become more and more popular.

Reference:
Patent; MERCK SHARP & DOHME CORP.; KUDUK, Scott, D.; REGER, Thomas, S.; ROECKER, Anthony, J.; (0 pag.)WO2016/85783; (2016); A1;,
1,2,3-Triazole – Wikipedia,
Triazoles – an overview | ScienceDirect Topics

Related Products of 288-36-8, New Advances in Chemical Research in 2021. Chemo-enzymatic cascade processes are invaluable due to their ability to rapidly construct high-value products from available feedstock chemicals in a one-pot relay manner. 288-36-8, name is 1H-1,2,3-Triazole, molecular formula is C2H3N3, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, below Introduce a new synthetic route.

1- (3-CHLORO-PROPOXY)-4-NITRO-BENZENE (7 g, 32.5 mmol) is dissolved in 2-methyl- 2-butanol (35 ml) followed by the addition of 1H-1, 2,3-triazole (3.43 g, 48.7 mmol), potassium iodide (0.54 g, 3.25 mmol) and sodium hydroxide (1.95 g, 48.7 mmol). The mixture is stirred for 20 h at 120 C, evaporated to dryness and suspended in toluene. Washing with water, drying over sodium sulfate and concentration in vacuo yields a crude product, which is washed with ether yielding L- [3- (4-NITRO-PHENOXY)-PROPYL]-LH- [L, 2,3] triazole as a colorless solid. Yield 6 g (75 %) MS: M = 249.3 (API+) H-NMR (400 MHz, CDC13) : 2.48 (m, 2H), 4.07 (t, J = 5.77 Hz, 2H), 4.64 (t, J = 6.7 Hz, 2H), 6.93 (d, J = 9.3 Hz, 2H), 7.56 (s, 1H), 7.72 (s, 1H), 8.20 (d, J = 9.2 Hz, 2H).

By the way, if you are interested in learning more fun chemistry with your kids, get your hands into one chemistry set now, and start enjoying the best part of chemistry: experiments about 1H-1,2,3-Triazole.

Reference:
Patent; F. HOFFMANN-LA ROCHE AG; WO2004/96796; (2004); A1;,
1,2,3-Triazole – Wikipedia,
Triazoles – an overview | ScienceDirect Topics

New discoveries in chemical research and development in 2021. The transformation of simple hydrocarbons into more complex and valuable products via catalytic C–H bond functionalisation has revolutionised modern synthetic chemistry. 288-36-8, name is 1H-1,2,3-Triazole belongs to triazoles compound, it is a common compound, a new synthetic route is introduced below. 288-36-8

Step 1) Synthesis of 5-methyl-2- (2H-1, 2, 3-triazol-2-yl) benzoic acid To a solution of N, N-dimethylformamide (30 mL) were added sequentially 2H-1, 2, 3-triazole (3.45 g, 50 mmol) , 2-iodo-5-methyl benzoic acid (5.24 g, 20 mmol) , cesium carbonate (11.72 g, 36 mmol) , trans-N, N’-dimethyl-1, 2-cyclohexanediamine (0.51 g, 3.6 mmol) and cuprous iodide (0.38 g, 2 mmol) . The reaction was heated to 100 ? under N2. After reaction for 4 hours, the reaction mixture was cooled to rt, diluted with water (60 mL) and extracted with ethyl acetate (200 mL × 2) . The aqueous layer was acidified to pH 1 to 2 with concentrated hydrochloric acid, and then extracted with ethyl acetate (200 mL × 2) . The combined organic layers were dried over anhydrous sodium sulfate, and filtered. The filtrate was concentrated in vacuo and the residue was purified by silica gel column chromatography (DCM/methanol (v/v) =50/1) to give the title compound as a yellow solid (2.76 g, 68 %) .MS (ESI, neg. ion) m/z: 202.1 [M-H] -;1H NMR (CD3OD, 600 MHz) d (ppm) : 7.88 (s, 2H) , 7.66 (d, 1H) , 7.59 (d, J= 8.2 Hz, 1H) , 7.50-7.48 (dd, J = 8.1 Hz, 1.1 Hz, 1H) , 2.45 (s, 3H) ; and13C NMR (CD3OD, 151 MHz) d (ppm) : 169.8, 140.7, 137.5, 136.7, 133.5, 131.5, 129.3, 126.0, 21.0.

I hope this article can help some friends in scientific research. I am very proud of our efforts over the past few months and hope to 1H-1,2,3-Triazole help many people in the next few years.

Reference:
Patent; SUNSHINE LAKE PHARMA CO., LTD.; ZHANG, Yingjun; JIN, Chuanfei; ZHANG, Ji; (90 pag.)WO2017/88759; (2017); A1;,
1,2,3-Triazole – Wikipedia,
Triazoles – an overview | ScienceDirect Topics